1、墙板和天花吊顶板在组装之前应对板材的材质、品类、規格尺寸、特性以及夹心板的芯材进行检查、核实是否能满足设计要求；必要时对取样进行功能测试（阻燃性、安全性不含毒性、抗压强度等特性）。
1. Before the assembly of wallboard and ceiling board, the material, category, specification, size and characteristics of the board and the core material of sandwich board shall be checked to verify whether they can meet the design requirements; If necessary, the sampling shall be subject to functional test (flame retardancy and safety, excluding toxicity, compressive strength and other characteristics).
2、墙板和天花吊顶板在组装之前应对天花吊顶上、夹墙内已施工完成后的隐藏工程进行工程验收，并达到合格要求，方能进行墙板和天花吊顶板的施工。
2. Before the assembly of wallboard and ceiling board, the concealed works on the ceiling and in the sandwich wall after construction shall be accepted and meet the qualified requirements before the construction of wallboard and ceiling board can be carried out.
3、天花吊顶板和墙板在组装时空气过滤器送风口、灯具、感温感烟元件、扬声器以及门、窗、管道的穿板处，其洞口周围要整齐、严密、清洁、不产尘，其缝隙应用不燃材质封堵；检查口的周边也要很好的封口。
3. At the air filter air supply outlet, lamps, temperature and smoke sensing elements, loudspeakers, doors, windows and pipe penetrations during the assembly of ceiling panels and wall panels, the openings shall be neat, tight, clean and free of dust, and the gaps shall be sealed with non combustible materials; The periphery of the inspection port shall also be well sealed.
4、天花吊顶板和墙板的拼缝应均匀一致，拼缝的间隙误差应不得超过0.5毫米，拼缝应用密封胶均匀封口，封口处应整齐、光滑、略低于板面。
4. The joint of ceiling plate and wall plate shall be uniform, and the gap error of joint shall not exceed 0.5mm. The joint shall be evenly sealed with sealant, and the sealing part shall be neat, smooth and slightly lower than the plate surface.
5、墙板组装应垂直，天花吊顶板组装应水平，板面整齐，部位准确，墙与地、墙与顶、墙与墙、顶与顶相互之间的相接处应有合理的结构设计，保证封口，防止开裂，拐角处宜为圆角。
5. The wallboard assembly shall be vertical, the ceiling board assembly shall be horizontal, the board surface shall be neat and the position shall be accurate. The joints between wall and ground, wall and top, wall and wall, top and top shall have reasonable structural design to ensure sealing and prevent cracking. The corners should be rounded.
6、板材组装的垂直角度≤1.5毫米，表面平面度≤1.5毫米，板与板相互之间，接口处的高低差≤1.0mm。
6. The vertical angle of plate assembly is ≤ 1.5mm, the surface flatness is ≤ 1.5mm, and the height difference between plates and at the interface is ≤ 1.0mm.
7、板材组装后应进行保护防止碰撞破坏板面。
7. After the plate is assembled, it shall be protected to prevent the plate surface from being damaged by collision.
8、板材表面应整齐、光滑、色泽一致，板材表面的保护膜应完好无损，交工前再撕膜。彩钢夹芯板隔墙
8. The plate surface shall be neat, smooth and consistent in color. The protective film on the plate surface shall be intact and torn before handover. Color steel sandwich panel partition
